Interior · 7 min read
Painting a Kitchen: Degrease First, Then Everything Else Sticks
Kitchen walls collect an invisible film of cooking grease that makes paint bead up and peel. Here is how to clean, prep, prime and finish the room properly.
Painting a kitchen starts with cleaning. Degrease the walls and ceiling, rinse, and let them dry. Then scrape, sand, patch, caulk and spot-prime stains. Finish with a washable satin or semi-gloss paint in even coats, and let it cure before scrubbing, so the film bonds and stays put.
Key takeaways
- Grease and cooking film are a common cause of peeling and beading in kitchen paint, so degrease walls and ceilings before sanding or priming.
- Pay extra attention behind the stove, around the range hood, above the cabinets and near the sink.
- Use a washable sheen, usually satin on walls and satin or semi-gloss on trim, and prime stains with a stain-blocking primer.
- Let the paint cure before scrubbing, and keep the range hood working.
Sherwin-Williams colors in this guide
Jump to a section
- Why is kitchen paint different from a living room?
- How do you degrease kitchen walls and ceilings?
- Which areas need extra attention?
- What repairs and primer does a kitchen need?
- Which sheen and color suit a kitchen?
- What gets skipped in a rushed kitchen job?
- How should the ceiling and trim be handled?
- When can you scrub the walls and cook normally?
- Questions
Why is kitchen paint different from a living room?
Cooking releases fine droplets of oil and steam that settle on every nearby surface. Over years they form a thin, sticky film that you may not see until you run a rag over the wall. Paint does not bond to grease, and what looks like a sound wall can peel in sheets or show beaded patches called fisheyes.
In older Grosse Pointe homes, a kitchen may have plaster walls, original trim and decades of stacked paint layers, and any one of those coats may have gone on over film that was never washed off. A careful job begins by treating the film, not the color.
How do you degrease kitchen walls and ceilings?
Work from the top down, and change rinse water often so grease is not just moved around.
- Cut the power nearby. Switch off the breakers for the outlets, switches and light fixtures near the wall, keep water out of them, and plan around the refrigerator on any circuit you turn off. Then unscrew the switch plates.
- Dust next. Wipe cobwebs and dust with a damp cloth, or use a HEPA-filter vacuum in an older house rather than dry sweeping, especially above cabinets and around the range hood.
- Wash with a degreasing cleaner. Use a cleaner made for kitchen grease, following the label. Some painters use TSP or a TSP substitute. Wear gloves and eye protection, and never mix cleaners. Test a hidden spot first, especially on old, flat or chalky paint, which can wash off under hard scrubbing.
- Rinse with clean water. Leftover cleaner can interfere with paint just as grease does.
- Dry completely. Give the wall time before sanding or priming.
- Do the water test. Flick a few drops of water on a flat or eggshell wall. If they bead up in patches, film is still there, so clean again. Glossy paint beads water naturally, so compare against a clean spot far from the stove.
Our guide to how to clean painted walls goes deeper on cleaners and technique.
Which areas need extra attention?
These places collect the most grease, moisture and wear, and they are where a rushed job shows first.
- Behind and beside the stove. The wall nearest the cooktop often carries the heaviest film. Wash it twice.
- Around the range hood. Hood housings and the wall above are sticky and dusty. Mask the hood, or take off removable panels.
- Above the cabinets. Dust and grease sit on top of cabinets and the soffit area, hidden but still part of the paint surface.
- Beside the sink and windows. Splashes loosen paint and leave water marks on sills and casings.
- Switch plates and outlet covers. They collect grease and fingerprints. With the power off, clean or replace them, and leave the switches and outlets themselves alone.
- Door and window casings. Handled like any trim: clean, scuff-sand, caulk the joints, then spot-prime.
A note on cabinets: this guide covers walls, ceilings and trim. Cabinet refinishing is a separate specialty from wall painting, so if cabinets are on your list, ask any painter whether they are in the written scope.
What repairs and primer does a kitchen need?
Once the surface is clean and dry, the usual sequence applies: scrape loose paint, sand the edges, fill holes and cracks, sand the fills smooth, caulk joints, then spot-prime.
- Old paint. Homes built before 1978 may have lead-based paint, and scraping, sanding or scuff-sanding it, trim included, can create lead dust. The EPA’s Renovation, Repair and Painting rule requires certified firms and lead-safe work practices for paid work that generally disturbs more than 6 square feet of painted surface per room inside, so read it before you start. For cleanup in an older house, wet-wipe and use a HEPA-filter vacuum rather than an ordinary household vacuum or dry sweeping, which can spread fine dust.
- Glossy or oil-based trim. Dull the sheen and use a bonding primer, as our guide on painting over oil-based and glossy paint describes.
- Stains. Water rings and smoke stains can bleed through ordinary paint, while grease spots have to be washed off first. Use a stain-blocking primer; many painters choose shellac- or oil-based versions, so read the label, ventilate, and keep flames and pilot lights, including a gas range, off or away while the primer is wet, because the vapors are flammable. See our explainer on stain-blocking primers.
- Patches. Spot-primed patches avoid dull “flashed” spots. Unprimed patches are one of the most common causes of uneven sheen.
- Caulk. Use a paintable flexible caulk along trim and the tops of baseboards, and leave the gap at the floor alone. Where a wall meets a countertop or tile backsplash, use a kitchen-and-bath caulk and check the label to see whether it can be painted.
Painting rooms like this in Grosse Pointe?
Tell us about your home and we’ll be in touch to talk it through.
Which sheen and color suit a kitchen?
A kitchen gets wiped down, so sheen matters. Satin is a common wall choice because it cleans easily without showing as many flaws as semi-gloss. Satin or semi-gloss on trim and doors resists scuffs and grease. A flat finish on the ceiling hides imperfections but can hold grime, so some people choose a washable ceiling product over the stove; check the label.
Higher sheen is more washable and shows more flaws, and the sheen should be consistent across a single wall. Our sheen guide explains the reasoning, and our kitchen and bathroom paint guide covers product types.
Color and kitchen light
Kitchens have task lights, under-cabinet bulbs, daylight, and often a mix of bulb temperatures, so a color can look different over the sink than by the table. Warm whites such as Alabaster SW 7008 and Greek Villa SW 7551, greiges such as Agreeable Gray SW 7029 and Accessible Beige SW 7036, and green and green-gray options such as Clary Sage SW 6178 or Sea Salt SW 6204 are worth sampling beside wood or white cabinets and stone counters. Our guide to kitchen wall paint colors compares them.
Screens and paint chips mislead. Paint a large sample on the actual wall, check it in morning, midday and evening light with the kitchen lights on, and look at it beside the counter and backsplash.
What gets skipped in a rushed kitchen job?
A few checkable details separate a kitchen that stays good from one that starts failing in the first year.
- The wash and the second rinse. If the wall feels slightly tacky or slick, it is not ready.
- The water test, which takes ten seconds and shows whether film is still on the surface.
- The upper walls and the ceiling, which look clean from the floor but can carry plenty of film.
- The corner where cabinet tops meet the wall, which needs caulk and a brush, not a roller.
- Light switches, outlet plates and vent covers, which are removed or masked rather than painted around.
- A look at the finished wall in raking light from the window, then again with the kitchen lights on, to find skipped spots and sheen shifts.
Rolling works well on flat wall areas, but around the range hood, tight corners and trim, a brush gives a straighter, cleaner line. A steady brush hand matters more here than speed.
How should the ceiling and trim be handled?
Painting order matters in a kitchen. A common order is ceiling first, then walls, then trim, so drips and spatter land on surfaces still to be painted. Our guide to cutting in and taping clean lines explains the edges, and the same logic applies where wall meets backsplash or cabinet.
Trim in a kitchen takes the most handling, from hands, cleaning cloths and steam. Degrease glossy trim, scuff-sand it, wipe off the dust, prime bare spots, and sand lightly between coats for a smooth finish. A satin or semi-gloss with consistent sheen across all trim in the room looks deliberate; mixed sheens look like patchwork.
When can you scrub the walls and cook normally?
Paint is dry to the touch in hours and keeps curing for weeks. You can usually cook again soon, but aggressive scrubbing too early can burnish or mark the film. Keep the range hood on and the room ventilated. Our guide to dry time versus cure time explains the difference, and small marks are easy to fix later.
In a Michigan winter the windows stay shut and the furnace runs, so lean on the range hood and keep the room within the temperature range printed on the can while the paint cures.
- Until the cure time on the label has passed, wipe spills with a soft, damp cloth and skip scouring pads and strong cleaners.
- Blot fresh splatters instead of rubbing them, since hard rubbing can burnish or smear the soft film.
- Keep a little leftover paint, labeled with the room and date, for touch-ups once the wall has cured.
Guiffre’s Painting Co. approaches interior painting this way: floors and furniture are protected, surfaces are cleaned, loose paint is scraped, holes are filled, joints are caulked, bare or stained areas are primed, and Sherwin-Williams paint goes on in even coats. Bob and Bobby are on every project, and a final walkthrough covers touch-ups.
Questions
Why does paint bead up or peel on kitchen walls?
Cooking grease forms a thin film that paint cannot bond to, which leads to peeling, beading called fisheyes and patchy coverage. Washing with a degreaser and rinsing is one of the steps that most affects how long the paint lasts. Let the wall dry fully before sanding or priming.
What finish do kitchen trim and ceilings need?
Trim and doors often get satin or semi-gloss because they resist scuffs and grease, while walls commonly get satin. Ceilings are usually flat, though some people choose a washable ceiling product over the stove, so check the label. Higher sheen cleans better but shows more flaws, so prep matters.
How long before I can scrub new kitchen paint?
It may feel dry in hours, but paint keeps curing for weeks. Wait for the cure period on the label before scrubbing, and use a soft cloth with mild cleaner until then.
About the author
Guiffre's Painting Co.
Family-owned interior painting and plaster repair serving Grosse Pointe and Metro Detroit. Owner Bob Guiffre has been painting for more than 37 years — more than 1,800 homes — and his son, Bobby, works beside him on every project. We paint with Sherwin-Williams. Estimates are free. Insured: $1,000,000 general liability. Call (586) 722-3277.