Interior · 7 min read
How to Paint Interior Doors, From Six-Panel Doors to Closet Doors
A door gets handled every day, so the finish has to be smooth and hard. Here is how to do it in the right order, hung or flat, without sticking or drips.

To paint an interior door well, take off the hardware, clean and sand every surface, prime bare spots and glossy paint, then paint the panels first, the muntin and rails next and the stiles last, ending with long strokes along the grain. Coat the top and bottom edges, and let the paint harden before shutting the door tight.
Key takeaways
- Remove the hardware, clean and sand the door, then prime bare spots and any glossy old paint before the finish coats.
- On panel doors, paint the recessed panels first, then the center muntin, the horizontal rails and the outer stiles, finishing with light strokes along the grain.
- Seal the top and bottom edges, and let the paint harden before shutting the door tight or it may stick in the frame.
- Match the sheen of the door to the casing and baseboards so the whole room’s woodwork reads as one.
Sherwin-Williams colors in this guide
Jump to a section
- Should you paint a door hanging or lay it flat?
- What prep does a door need?
- When does a door need primer?
- What order do you paint a six-panel door in?
- Do you need to paint the top and bottom edges?
- Why do freshly painted doors stick, and how do you prevent it?
- What about closet, louvered and glass-paneled doors?
- Which sheen and color should doors be?
- Questions
Doors are among the most-touched painted surfaces in a house, and a door that sticks in its frame after painting is a familiar complaint. Most problems trace back to preparation and order of work.
Should you paint a door hanging or lay it flat?
Laying a door flat on padded sawhorses gives the smoothest result, because runs become much less likely, and it puts the top and bottom edges within easy reach. Painting on the hinges works for a careful painter, but brush thinner coats and watch for runs.
If you take the door off, tap out the hinge pins and label the hinge edge with the room and opening, because in many older houses a door was fitted to one opening and may not fit another. Lay it on padded stands over a clean drop cloth, paint one face, and flip it only after that side has dried.
If you paint it on its hinges, wedge it open, protect the floor under it and open it just far enough to reach the edges. Paint all four edges, not only the faces you see.
What prep does a door need?
Remove knobs, strike plates, latches and hinge plates if you can. Masking tape around a doorknob often leaves a ragged line, and paint that gets into the latch mechanism can make it stick or bind. Put small screws in a labeled bag or tape them to the hardware itself.
Then clean the door. Doors collect hand oils around the handle, and paint will not hold to oily residue. If the door hangs beside a switch or outlet, turn the power off to it first and keep the cloth well wrung out. Wash with a degreasing cleaner, rinse and let the door dry.
Next, scrape anything flaking, sand the surface with fine paper (scuff-sand glossy areas so the primer has something to grip), wet-wipe off the dust, and fill dings and nail holes, sanding the fills flush once they dry. Our guide to sanding and caulking trim covers the technique in more detail.
- Check the panels for thin lines where the wood has shrunk away from its frame, and fill them with a flexible, paintable caulk rather than hard filler.
- Check the bottom edge for bare wood or swelling from past wet floors.
- Look closely at the corners of panel moldings, where old paint tends to bridge and fill the profile.
When does a door need primer?
Once the fills are sanded, the dust is wiped away and the door is dry, prime any bare wood, patches and sanded-through areas. If the existing paint is a hard, glossy oil-based enamel (often found on 1920s through 1950s doors), use a bonding primer after scuff-sanding, because latex paint applied straight over old gloss can peel or scratch off; check the primer label for what it can go over. Our guide to painting over oil-based and glossy paint explains the adhesion test, and do you need primer before painting explains when it is optional.
If the wood is stained, or has knots or tannins that might bleed through, a stain-blocking primer is the safer choice, and our guide to stain-blocking primers explains the types. Many are shellac- or oil-based, so read the label for ventilation requirements.
What order do you paint a six-panel door in?
The rule for panel doors is panels first, then the center muntin, then the rails, then the outer stiles. A traditional six-panel door has two vertical stiles at the sides, a vertical muntin between the two columns of panels, and four horizontal rails: top, bottom and two in between, one of which carries the lock. The six recessed panels sit inside that frame. Painting in the wrong order leaves lap marks where wet paint meets paint that has begun to set.
- Paint the molded edges and recessed faces of each panel, working from the top panels down. Brush the paint out of the corners so it does not collect.
- Paint the center muntin from top to bottom.
- Paint the horizontal rails across the door, from the top rail down.
- Paint the two outer stiles from top to bottom, finishing with long, light strokes along the grain.
Flush (flat) doors, found in many post-war Colonials, Capes and ranches across Metro Detroit, are simpler, but they show brush marks and roller texture more than panel doors do. Use a small foam or fine-nap roller and a brush for the edges, working in sections and keeping a wet edge, then lay off with light strokes in one direction. Hollow-core doors are light, so brace them so they do not slide or wobble while you work.
Painting rooms like this in Grosse Pointe?
Tell us about your home and we’ll be in touch to talk it through.
Do you need to paint the top and bottom edges?
Yes. Bare edges soak up humidity and can swell, one reason doors stick in humid Michigan summers near Lake St. Clair. Seal the top and bottom with primer and paint, and coat the latch and hinge edges too, keeping those coats thin so paint does not build up where the door runs close to the jamb.
The hinge edge is the one that gets forgotten, and the bottom edge is the one most exposed to mop water and damp floors.
Why do freshly painted doors stick, and how do you prevent it?
Paint that feels dry may still be soft underneath. If the door is closed against a frame painted at the same time, the soft surfaces can bond (this is called blocking) and tear when you open it. Prevention is mostly patience:
- Leave the door open as long as is practical, and check the paint label for its recoat and cure guidance before closing it fully.
- Use a paint labeled for trim and doors; many are formulated to resist blocking, though it varies by product. Check the can.
- Keep each coat thin. Two thin coats dry and harden better than one thick one.
- Rehang the door only after the paint has dried hard, and avoid slamming it for the first days.
Dry and cured are different things, and full cure takes weeks. Our guide to paint dry time versus cure time explains why you should be gentle with a new finish.
Before the door goes back on its hinges, or gets shut for the night, check it in raking light for runs at the panel corners, bare spots on the top and bottom edges, paint in the latch hole or hinge mortises, and tacky patches where the door will touch the stops. These are far easier to fix now than after the paint has set.
What about closet, louvered and glass-paneled doors?
Bifold and sliding closet doors are easiest to paint flat with the hardware off. On louvered doors, brush each slat from the top down, undersides included, in thin coats, because louvers trap paint and drip. Keep paint off the track, pivots and rollers, and go easy on the edges that ride in the track; buildup there is a common reason closet doors bind.
Glass-paneled doors, such as the French doors found in many older homes, are mostly brush work. Paint the thin dividers (muntins) around each pane with a small angled sash brush, bringing the paint right up to the glass line and keeping the bristles on the wood. If paint lands on the glass, let it dry, then run the corner of a sharp razor blade along the paint line to score it and lift the stray paint off the glass, keeping the blade away from the finished wood.
Which sheen and color should doors be?
Satin or semi-gloss is typical for doors, since they need to be washable. Keep the sheen the same as the casing and baseboards in the room. Color is the bigger choice. Extra White SW 7006, a bright, crisp white that leans slightly cool, and Pure White SW 7005, a soft, clean white with a touch of warmth, are both classic choices for woodwork in a Colonial Revival interior, while a deeper door color can be a design feature. Test a large sample on a real door in the room’s light, because screens and chips mislead. Our guide to painting baseboards, casings and chair rails explains why the door should match the rest of the trim.
For a closer look at doors in a traditional home, see painting Colonial Revival interiors. If you would rather hand the work over, interior painting from Guiffre’s Painting Co. includes panel doors and frames and starts with the same kind of preparation: protecting floors and furniture, cleaning, scraping, sanding, filling and priming bare areas, followed by Sherwin-Williams paint in even coats and a final walkthrough with touch-ups.
Questions
Should I remove an interior door to paint it?
Laying a door flat on padded sawhorses gives the smoothest finish and fewest drips, and it makes the edges easier to reach. Painting on the hinges works if you are careful and brush thin coats. Either way, take off the knob, latch and strike plate rather than taping around them.
Why does my freshly painted door stick?
Paint that feels dry can still be soft, and a soft painted door can bond to a soft painted frame. Leave the door open as long as is practical, follow the label’s recoat and cure guidance, apply thin coats, and avoid building up paint on the edges. Full cure can take weeks.
What order do you paint a panel door?
Paint the recessed panels first, then the center muntin, then the horizontal rails, and finish with the outer vertical stiles, ending with long strokes along the grain. This order avoids lap marks where wet paint meets paint that has started to set.
About the author
Guiffre's Painting Co.
Family-owned interior painting and plaster repair serving Grosse Pointe and Metro Detroit. Owner Bob Guiffre has been painting for more than 37 years — more than 1,800 homes — and his son, Bobby, works beside him on every project. We paint with Sherwin-Williams. Estimates are free. Insured: $1,000,000 general liability. Call (586) 722-3277.