Request a free estimate Call (586) 722-3277

Older Homes · 7 min read

Painting 1920s Tudor Revival Interiors: Plaster, Dark Woodwork and Arches

Tudor Revival rooms reward patience. The textured walls, arches and dark wood that give them character also make them unforgiving to rush.

Painting a 1920s Tudor Revival interior often means working with textured plaster, arched openings, dark woodwork and a fireplace. A careful job cleans and repairs the plaster first, protects the dark wood or paints it deliberately, brushes the curves and details, and picks flatter sheens so the texture looks soft rather than shiny.

Key takeaways

  • Textured plaster is painted with a thick-nap roller and a brush, and flat or low-sheen paint keeps the texture soft instead of shiny.
  • Decide early whether dark woodwork and beams stay as they are, because painting stained wood is hard to undo.
  • Arched openings, leaded windows and mantels are mostly slow brush work with careful caulking and masking.
  • Test before you scrape or sand in a home built before 1978, and if asbestos turns up, leave it undisturbed and ask a qualified professional.

Sherwin-Williams colors in this guide

Jump to a section
  1. What makes Tudor Revival interiors different to paint?
  2. How do you paint textured plaster?
  3. Should you paint the dark woodwork and beams?
  4. How do you paint arched openings and curved plaster?
  5. What about leaded windows, fireplaces, radiators and beams?
  6. What order should the work follow in a Tudor room?
  7. What prep gets skipped most often in these rooms?
  8. Questions

What makes Tudor Revival interiors different to paint?

Tudor Revival was at its height in the 1920s, and the style shows on the inside as much as the outside. Many Grosse Pointe and Metro Detroit examples have steep gables, half-timbering, tall chimneys and leaded or divided-light windows outside. Inside, rooms in this style often include some of the following.

  • Textured or hand-troweled plaster walls, sometimes with a heavy, uneven finish
  • Arched doorways and, in some rooms, wall niches
  • Dark stained woodwork and, in some houses, paneling, exposed beams or decorative timbers
  • Leaded or divided-light windows
  • A substantial fireplace, sometimes with a carved or paneled mantel

A rushed job usually fails where two of these meet.

One caution runs through almost all of them. In a house built before 1978, painted trim, doors, radiators and windows may carry lead paint, and older plasters, textured finishes and joint compounds may contain asbestos. Scraping, sanding, scuff-sanding and wire-brushing can release that dust, so have suspect surfaces tested first; the EPA’s homeowner guidance on asbestos notes that you generally cannot tell by looking and advises leaving sampling to a trained, accredited professional. If asbestos turns up, leave the material undisturbed and talk to a qualified asbestos professional about whether to leave it, seal (encapsulate) it or remove it; do not scrape, sand, roll or spray it yourself. For lead dust, wet-wipe surfaces and use a vacuum with a HEPA filter rather than an ordinary household vacuum or dry sweeping. The EPA’s Renovation, Repair and Painting (RRP) rule requires certified firms and lead-safe work practices for paid work that generally disturbs more than 6 square feet of painted surface per room inside a pre-1978 home. When textured plaster is cracked or loose, repairing the plaster first keeps new paint from failing along the same line.

How do you paint textured plaster?

Texture is the feature, so the goal is to color it without filling it. A few details separate a good result from a flat, clogged one.

  1. Clean first. Dust and cobwebs collect in texture. Use a HEPA-filter vacuum with a soft brush attachment, then wipe off grime with a lightly damp sponge and mild cleaner, using as little water as possible, because old plaster does not like soaking. Switch the power off at the breaker before wiping near outlets, switches or fixtures. Primer only bonds to a clean surface.
  2. Repair, then feather. Cracks and holes are filled, but the repair is blended into the texture, by stippling or dabbing the compound to match, instead of sanded flat, or it will show as a smooth patch.
  3. Prime the patches. Bare spots and fills are primed so they do not flash.
  4. Use a thick nap. A deep-nap roller pushes paint into the valleys, and a brush follows into any spots the roller skips. Look in raking light for tiny unpainted pockets.
  5. Keep it flat. Flat or matte on the walls and ceiling hides waves and keeps the texture from catching glare.

Hairline cracks are common in old plaster, especially after dry, heated Michigan winters, and tend to show at arches and window corners. The National Park Service’s Preservation Brief 21 on repairing historic flat plaster describes filling hairline cracks with patching material or joint compound and bridging recurring ones with fiberglass mesh tape. Our plaster walls guide covers the general approach, and hairline cracks that keep coming back explains how to repair cracks so they stay closed.

Should you paint the dark woodwork and beams?

This is the biggest decision in a Tudor Revival room. Dark stained woodwork is part of the style, and once it is painted it is very hard to return to a stain.

  • Is the wood in good condition, with an intact finish? If so, cleaning and refreshing it is often enough.
  • Does the room feel too dark even in daytime? Lighter wall color may fix that while the wood stays.
  • Is the finish worn, sticky or damaged? That may justify repainting, with proper prep.

If you do paint woodwork, start by cleaning off old furniture polish and wax, which can make paint bead up. A glossy or varnished surface must then be scuff-sanded, with the precautions above, and primed with a bonding primer, or the new paint can peel.

Tannin-rich or stained wood may need a stain-blocking primer so color does not bleed through, and open-grained woods such as oak will show their grain through paint unless it is filled first. Read the labels. Our decorative woodwork and paneling guide goes deeper.

Painting rooms like this in Grosse Pointe?

Tell us about your home and we’ll be in touch to talk it through.

Request a free estimate

How do you paint arched openings and curved plaster?

Arches are mostly brush work (our guide to painting arched doorways and curved plaster goes further). A small roller may handle a flat arch face, but it can’t reach into the curve or tight edges, and ordinary masking tape is hard to bend cleanly around it. A flexible tape or a carefully brushed line works better.

  • Caulk the joint where trim or an inset meets the curve, using paintable caulk.
  • Cut the edge in slowly with an angled brush, loading it lightly.
  • Check the arch in raking light for drips, since curves hide them at first glance.
  • Keep the sheen the same across the arch and the flat wall so the curve does not look patchy.

Rounded (bullnose) corners often go with arches and chip easily, so check that any bare edge is primed before the finish coats.

What about leaded windows, fireplaces, radiators and beams?

Leaded and divided-light windows. The lead came and the putty are delicate. Clean gently and keep paint off the glass, the lead and the weatherstripping. If putty is crumbling or a pane sags, that is a job for a window specialist, not a paintbrush. Our guide to steel casement and leaded windows explains the care involved.

Fireplaces. Wood mantels are painted like trim, with cleaning, scuff-sanding and the right primer. Never paint inside the firebox. Near the opening, use heat-tolerant paint and check the label. Soot and smoke stains need a stain-blocking primer before the finish coat or they show through.

Let the paint cure before lighting the first fire, since heat on fresh paint can smell or discolor it, and check the label for how long to wait. Painting a brick or stone surround is a one-way decision, so think it through first. Our guide to painting fireplace mantels and surrounds covers the details.

Radiators. Many houses of this era still have them. Clean and de-rust each one, keeping the dust precautions above in mind, paint only when it is completely cool, use a paint made for heated metal (check the label), keep the coats thin, and never paint a valve or bleeder shut. A faint odor the first time it heats is common. See painting radiators and baseboard heat.

Beams and plaster ceilings. Rough or hand-hewn beams hold dust and cobwebs in the grain, so vacuum them with a HEPA-filter vacuum and brush attachment before priming. Beams and high ceilings need safe, stable access, which is worth asking about before the work starts.

What order should the work follow in a Tudor room?

Order matters more in a room with this much detail, because every surface touches another one.

  1. Walk the room with a flashlight. Tap the plaster for hollow spots, and look for ceiling stains, soot at the fireplace and loose putty at the windows. Anything found belongs in the written scope, and in a pre-1978 house this is the moment to have suspect paint or textured finishes tested.
  2. Protect the floors, the fireplace hearth and any furniture that cannot leave the room.
  3. Clean (with the power off near outlets, switches and fixtures), repair and caulk the ceiling, walls, arches and trim.
  4. Once repairs are fully dry, prime patches, bare wood and any stained spots.
  5. A common order is the ceiling first, then the walls, then the trim, with beams and mantels fitted in where their sheen and color call for it.
  6. Walk the room in raking light and in daylight, then touch up.

Hardwood floors and area rugs in older homes deserve real protection. Drop cloths that slide are a hazard, so check that coverings are taped or weighted at the edges. Plaster dust travels, so close off doorways to the rest of the house.

Give the room time between coats. Paint dries slowly in humid air, common in Michigan summers, so a coat applied too soon can pull or lift. Check the can for recoat times and its temperature and humidity limits. Dry to the touch is not ready to recoat, and neither means fully cured.

What prep gets skipped most often in these rooms?

  1. Dust and grime left in textured plaster, which stops primer from bonding
  2. Smooth, sanded patches that stand out against the texture
  3. Glossy old finishes painted without a bonding primer
  4. Unprimed repairs that dull after the first coat
  5. Caulk left out at arches and trim, which opens as the plaster moves
  6. Paint on leaded glass, hardware, radiator valves or mantel edges

Guiffre’s Painting Co. protects floors, furniture and plants, cleans surfaces, scrapes loose paint, sands edges, fills holes and cracks, caulks joints and primes bare or stained areas before painting with Sherwin-Williams in even coats, as the process page explains. Bob and Bobby are on every project, and a final walkthrough with touch-ups wraps up the job. For the interior service overview, see our interior painting page.

Questions

Should I paint over dark wood in a Tudor Revival house?

Think carefully first, because painting stained wood is very hard to reverse. If the finish is in good shape, cleaning it and lightening the walls often fixes a dark room. If you do paint it, clean, scuff-sand and use a bonding primer, and a stain-blocking primer where wood may bleed.

What sheen works on textured plaster walls?

Flat or matte is the usual choice, because it hides waves and keeps texture from catching glare. Trim and doors can take satin or semi-gloss. Keep the sheen consistent across any one wall.

Can I paint inside a fireplace?

No. Do not paint inside the firebox. Wood mantels are painted like trim, and paint near the opening should be heat-tolerant according to its label. Smoke and soot stains need a stain-blocking primer first.

Cracks, holes or loose plaster?See how Guiffre’s repairs walls and ceilings so the paint over them looks right.

About the author

Guiffre's Painting Co.

Family-owned interior painting and plaster repair serving Grosse Pointe and Metro Detroit. Owner Bob Guiffre has been painting for more than 37 years — more than 1,800 homes — and his son, Bobby, works beside him on every project. We paint with Sherwin-Williams. Estimates are free. Insured: $1,000,000 general liability. Call (586) 722-3277.

Let’s talk about your home.

Tell us a little about the project and we’ll be in touch to talk it through and set a time to see it. Estimates are free.

Request a free estimate Call